De Berkey fabrikant heeft deze week een rechtszaak aangespannen tegen de EPA om een einde te maken aan de vervolging van Berkey waterfilters op basis van diens besluit dit jaar om Berkey waterfilters te behandelen alsof het pesticiden zijn in plaats van waterfilters. De EPA heeft inmiddels al opdracht gegeven om het grootste magazijn van Berkey te sluiten. Zie onze blogpost voor meer informatie. .
Verkrijgbaar per set van 2
2 filters zijn goed voor 3.785 liter water of voor 1 jaar, wat maar het eerst het geval is
Gemaakt van veilig loogvrij plastic
Gratis bezorging in de EU
De enige landen die hun water nog blijven fluorideren zijn Ierland en delen van Engeland en Spanje. In alle andere Europese landen is fluoridering stopgezet of nooit uitgevoerd. Zie de links beneden voor meer uitgebreide informatie over fluoridering van het water: Zie kaart voor het niveau van de fluoride stand in de UK of kaarten van wereldwijde fluoridatie.
Berkey PF-2 elementen zijn speciaal ontworpen voor gebruik in combinatie met de Black Berkey waterfilters om de volgende ongewenste elementen die gevonden worden in drinkwater te adsorberen
Het aantal PF-2 filters moet altijd gelijk zijn aan het aantal geïnstalleerde Black Berkey waterfilters. Bijvoorbeeld: 4 Black Berkeys (2 sets van 2) vereist 4 PF-2s (2 sets van 2), enzovoort.
Wij bevelen aan om onder normale omstandigheden de PF-2 elementen te vervangen na ongeveer 3.785 liter. Bijvoorbeeld: het Royal Berkey systeem bevat ongeveer 12,3 liter, dus de PF-2 filters moeten worden vervangen na (3.785:12,3) of 307 hervullingen. Als het systeem ongeveer één keer per dag wordt bijgevuld dan moeten de PF-2s worden vervangen na 10 maanden. Als het systeem twee keer per dag wordt gevuld dan moeten de PF-2s worden vervangen na ongeveer 5 maanden. De werkelijke capaciteit is afhankelijk van de aanwezigheid van andere concurrerende verontreinigende stoffen in het water. Hoge gehaltes van fluoride, arsenicum en zware metalen kunnen de capaciteit en prestaties van de PF-2 verminderen.
(Waarschuwing: De PF-2 filters moeten worden klaargemaakt voor gebruik)
Testing for fluoride was based on 20-30ppm of the ion in the influent aqueous solution at a flow rate of no more than 3 gpm (11 lpm) per cubic foot of media. Results of < 1ppm of the fluoride ion in the effluent were typical for the media (>95% reduction). Under optimum conditions, effluent concentrations of less than 50 ppb were readily achieved (>99.75% reduction). This product uniquely targets the entire family of arsenic oxide anions as well as the arsenic cations.
Our original tests were done using gravity alone to purge the PF-2 filters. Since then, we have added a step by using purging buttons which are much more efficient at removing any residual process dust from the PF-2 media. The test does not distinguish between activated alumina (Al2O3) and Aluminum (Al). So we had to use the total count of aluminum and activated alumina in our tests.
PF-2 filters contain high-grade activated alumina (Al2O3), which currently is the most efficient media available for extracting fluoride from water. Activated alumina is inert. Below are the results we obtained when testing the PF-2 filters (the water was not pre-filtered through the Black Berkey filter elements). The reduction over time is due to additional residual process dust being washed free from the PF-2 filter as the system is used. To give a scale for comparison purposes we include test results from a national brand toothpaste and water boiled in an aluminum pan.
While the above results indicate that the residual process dust adds a minute amount of activated alumina to the water, the Black Berkey water filters reduce aluminum from the water. We tested water that naturally contained .320ppm aluminum and filtered it through the combination of the Black Berkey and the post conditioned PF-2 filtration elements (5 cycles). The results showed a net reduction in aluminum contamination (Raw influent: .320ppm - Effluent after passing through the Black Berkey and PF-2 elements: .232ppm). Again, the standard tests cannot distinguish between aluminum (Al) and activated alumina (Al2O3), which is inert. Nevertheless, the tests showed a net reduction by the Black Berkey filter element in the combination of naturally occurring aluminum plus any residual activated alumina (Al2O3)process dust from the PF-2 elements.